VoyForums
[ Show ]
Support VoyForums
[ Shrink ]
VoyForums Announcement: Programming and providing support for this service has been a labor of love since 1997. We are one of the few services online who values our users' privacy, and have never sold your information. We have even fought hard to defend your privacy in legal cases; however, we've done it with almost no financial support -- paying out of pocket to continue providing the service. Due to the issues imposed on us by advertisers, we also stopped hosting most ads on the forums many years ago. We hope you appreciate our efforts.

Show your support by donating any amount. (Note: We are still technically a for-profit company, so your contribution is not tax-deductible.) PayPal Acct: Feedback:

Donate to VoyForums (PayPal):

Sun, December 22 2024, 01:24 [ Login ] [ Contact Forum Admin ] [ Main index ] [ Post a new message ] [ Search | Check update time | Archives: 1, 2, 3, 4, 5, 6, 7, 8, [9] ]

[ Next Thread | Previous Thread | Next Message | Previous Message ]

Date Posted: - Thursday - 10/ 5/06 - 2:48pm
Author: Capt'n Mike - Gypsy Mariner TM36
Subject: Stepped Masts
In reply to: Mike Anthony 's message, "Stepped the masts!!" on - Thursday - 10/ 5/06 - 11:21am

Mike,
Did you use the original wire inside the roller furling? Did it fit on o.k.? I figured it probably would. Congrats!

[ Next Thread | Previous Thread | Next Message | Previous Message ]

Replies:

[> [> [> [> Stepped the masts!! -- Mike Anthony, - Thursday - 10/ 5/06 - 4:17pm

Capt'n

Yes, the furler worked like a dream, thanks for that bit of information, otherwise I would have made a whole new head stay $$. The line from the Main to the Mizzen seems a little slack, however, I have not yet put the booms on, maybe that will pull enough to tighten it up.

Capt'n Mike, I thank you as well.



Mike


[ Edit | View ]

[> [> [> [> [> Triatic Stay -- Capt'n Mike, - Thursday - 10/ 5/06 - 8:56pm

Mike,
The triatic stay is the wire between the main mast and the mizzen mast. If this is what you are referring to, it can usually be tightened by adjustments to the several turnbuckles. Check each of the following turnbuckles to see if any of the studs either look like they are not far enough into the turnbuckle or too far into the turnbuckle:
1. Bobstay Turnbuckle and/or Headstay Turnbuckles - tightening will move the main masthead forward a little and, thus, tighten the triatic, but you will probably need to loosen the main backstay turnbuckles some;
2. Main Mast Backstay Turnbuckles - these can be loosened and it will move the main masthead forward, but you will need to take up the slack in the headstay and/or the bobstay (see # 1 above);
3. Triatic Turnbuckle - it is usually located at the mizzen side of the triatic but it is a total pain to adjust since you have to go to the top of the mizzen mast to it. If you attempt this tie yourself off real well at the mizzen masthead and tie your tools to yourself, otherwise you may hurt yourself or your crew below;
4. Forward and Aft mizzen lower shroud turnbuckles - these can be adjusted some (loosen forward and tighten aft) to move the mizzen masthead aft which will tighten the triatic. But make sure you don't overtighten or you could get the mast out of column.
5. Combination of 1 thru 4 - usually it is a combination of all of the above, but start by looking for turnbuckles that are barely able to be screwed into the studs or are all of the way screwed into the studs.
Hope this helps.
Capt'n Mike


[ Edit | View ]

[> [> [> [> [> [> Triatic Stay -- Mike Anthony, - Friday - 10/ 6/06 - 8:49am

Capt'n

Everything you say makes perfect sense, I will go around and make adjustments as needed. Again thanks for all of your input and help.

Island Mike


[ Edit | View ]


[ Contact Forum Admin ]

Forum timezone: GMT-5
VF Version: 3.00b, ConfDB:
Before posting please read our privacy policy.
VoyForums(tm) is a Free Service from Voyager Info-Systems.
Copyright © 1998-2019 Voyager Info-Systems. All Rights Reserved.