VoyForums: [E-mail] POT HEADS

[ Show ]

Support VoyForums

[ Shrink ]

VoyForums Announcement: Programming and providing support for this service has been a labor of love since 1997. We are one of the few services online who values our users' privacy, and have never sold your information. We have even fought hard to defend your privacy in legal cases; however, we've done it with almost no financial support -- paying out of pocket to continue providing the service. Due to the issues imposed on us by advertisers, we also stopped hosting most ads on the forums many years ago. We hope you appreciate our efforts.

Show your support by donating any amount. (Note: We are still technically a for-profit company, so your contribution is not tax-deductible.) PayPal Acct: Feedback:

Donate to VoyForums (PayPal):

(info) Warning About Aluminum Foil: Aluminum foil is way too thin, and will burn, releasing slightly toxic smoke that you do not want to be inhaling. You can test this by taking a little square piece of foil, and burning it under a lighter, you WILL see smoke rise off. Do you want to inhale that shit? (making bongs) Water Bong Supplies -Gallon Container (like a 1/2 gallon Gatorade bottle or jelly bean container)) -Plastic Tubing -1 foot long brass pipe or aluminum pipe -Knife or Drill (to make holes) -A bowl to smoke out of How to Make Take the gallon size container and make 2 holes in the top of it. One hole must be the diameter of the brass tubing, and the other the diameter of the plastic tubing. Insert the brass tubing down near the bottom of the inside of the container. Now take the plastic tubing (can get from hobby bench or home depot) and stick it through the second hole. Make it so this tube doesn't go more than 2 inches down into the container. Now take a bowl (from a pipe or homemade) and put it on top of the copper pipe. Be creative, you don't only have to use a brass tube, you can modify these designs as much as you want. Procedure Suck from the tube, duh! WaterFall Supplies -2 Liter Bottle/ 1/2 gallon gatorade bottle -A pipe/bowl How to Make Drill a hole in the bottom of the 2 liter bottle. Fill a bowl with marijuana and put it on the top of the bottle so that its airtight. This is easiest done by two different methods. One method is to take the cap of the 2 liter bottle your using. Drill a hole in the cap that matches the width of a glass or brass stem you own. Take the glass stem, or the brass stem and stick it into this hole. Procedure Put your finger on the hole at the bottom of the bottle. Take off the bowl on top, and fill the water to about 3 inches from the top with water. Screw back on the bowl/cap.. Put a lighter to the marijuana, and let your finger off the hole. The water will drain out of the hole, sucking air in from the top. This air is fucking filled with incredible amounts of smoke, and fills the bottle. By the time all the water drains out the bottle is so full it turns yellow. You can pass this thing around 5 people at least twice. It cash's huge bowls.. Steam Roller Materials -Cardboard Tube (could be a toilet paper tube) -A bowl or pipe -You may need tape or glue How to Make Take the cardboard tube, and make a hole in the side of one end. Take the bowl/pipe, and stick the end into it. When your done it should look like an oversized pipe. Procedure Put your hand over the end that has the pipe nearest to it. Suck from the other end. The end your hand is covering will work as a huge Carb. Light up the pot and suck, when you feel you've filled the cardboard tube full of smoke, let your hand off the carb and it will rush all the smoke into your lungs, it gets you REALLY REALLY fucked up. Make a Vaporizer!! Supplies -5 Gallon jug (you need this so the plastic wont melt at the top) -Small Soldering Iron (with screw off tip) -Screw -Thimble or Brass Plate that is bowl shaped -Light Dimmer (optional, read about it) Soldering Iron Find a soldering iron with a screw off tip. These can be found at ANY hardware story, Ace Hardware, Home Depot, and Home Base are obvious examples. Unscrew the tip. Find a screw that can screw into the hole you just made by unscrewing the tip. Just match the width of the hole with the width of a screw that size. Find a brass plate, or bowl shaped brass plate thing that you can drill a hole into. One with a hole already in it would be nice. Drill a hole that is the width of the screw into the brass bowl thing. Then screw the screw through the brass bowl into the soldering iron. You are done with this part. Hooking the Iron to the Jug This might be hard. You need to use a cap, that will fit onto the jug, but also allow the soldering iron to go through the cap also. Its illustrated below how it should look. If you can get the soldering iron to hook onto the jug, without a cap, do it. If you can't, make a hole in the cap that can fit the soldering iron through it, then snap or hook the cap to the 5 gallon jug. Dimmer Switch You can also add something called a "Dimmer Switch" which is used to dim or lighten lamps. You can use it with this to lower electricity to the soldering iron. This lowers the temperature at which the weed burns at, so if you want it to burn and produce more of a "smoke" you can raise the temperature. Remember, the point of a vaporizer is to make it so the THC doesn't get burned, because when you smoke it with a pipe under a flame it destroys around 50% of the THC. With a vaporizer only around 5% is destroyed. This is optional though, soldering irons usually only reach the temperature that vaporizes THC, about 210-220 degree's. Finish Now you should have the soldering iron in the jug, and it looks just about ready,....its not. Where are you going to suck the smoke out? This is where a nice drill would come in. Just drill, or cut a hole in the top of the bottle. Insert a tube that fits the size of the hole, then suck out of the tube.. You can also make a tube come out of it so you can suck farther away, its what I did. If you have any trouble figuring this out, which i did when i first saw plans, e-mail me, and I'll try to better explain it.