VoyForums
[ Show ]
Support VoyForums
[ Shrink ]
VoyForums Announcement: Programming and providing support for this service has been a labor of love since 1997. We are one of the few services online who values our users' privacy, and have never sold your information. We have even fought hard to defend your privacy in legal cases; however, we've done it with almost no financial support -- paying out of pocket to continue providing the service. Due to the issues imposed on us by advertisers, we also stopped hosting most ads on the forums many years ago. We hope you appreciate our efforts.

Show your support by donating any amount. (Note: We are still technically a for-profit company, so your contribution is not tax-deductible.) PayPal Acct: Feedback:

Donate to VoyForums (PayPal):

Login ] [ Contact Forum Admin ] [ Main index ] [ Post a new message ] [ Search | Check update time | Archives: 1 ]


[ Next Thread | Previous Thread | Next Message | Previous Message ]

Date Posted: 09:46:10 02/17/02 Sun
Author: Pex_nb
Subject: Re: anyone have a jtag schematic
In reply to: fred 's message, "anyone have a jtag schematic" on 20:09:14 02/12/02 Tue

>need jtag reader schematic or site where i can view
>schematic

Nice pic of a homemade jtag reader.
http://www.geocities.com/electronics1st/JTAG.html

I copied this months ago. Thought it may come in handy some time. I never tried it myself.
-------------------------------
Parts section:
I bought a 5 pack of 100 OHM 1/2 watt resistors from Radio Shack(wattage does not matter, 1/8 through 1/2 are fine).
Also I scrounged up a 25D(parallel) connector.
I also used a six inch piece of Cat5 cable I had laying around(keep it under 12" and you should be fine).

Connections to D25 section:
1) I soldered one wire to pins 18-25 on the D25 connector.
Really all I did was spread solder across those pins and then soldered the wire to it.
2) Soldered a 100 OHM resistor to each the following pins on the D25 connector.
Pins 2, 3, 4, 5, and 13.
3) I then soldered a wire from the Cat5 cable to the other end of each resistor.
4) I unplugged the IRD and unhooked all the cables to it.
Then I flipped it over and soldered the wires from the other end of the Cat 5 cable.
I counted the large pads on the right of the long ground pad by the following:
Top pad #1 etc. to the bottom pad #7.
Pad 1 and pad 7 are not used.
Next solder the wires that came from the 25D connector as follows:

Connections to IRD JTAG section:
Wire 2 to IRD pad 2
Wire 3 to IRD pad 3
Wire 4 to IRD pad 4
Now things change a bit:
Wire 5 to IRD pad 6
Wire 13 to IRD pad 5
Ground is easy, just solder the wire that came from pins 18-25 to the long ground block that should be to your left(no resistor on this wire).

Disclaimer:
That's it you are ready to dump.
From what I have read, this can be a dangerous way to hook it up(experts say a voltage spike can cause problems to both IRD and your computer) SO BE CAUTIOUS or do not use this method.

Software section:
I did NOT plug in the IRD till all connections were done and the computer was on.
I then ran the jtag_p.exe program.
It should show you the following:
IDCODE=2D4C9041(this is the most common code, there are others)
It will say it does not know that ID Code.
Just press y
Then where it ask's for starting address put 7FF80000
Then it ask's for length, put 80000
That will do a full dump(512K). It took a couple minutes on a 486 100 MHZ.
You can also do a partial dump to get just the Box Keys.
7FFFFFC0
0C
After dump is done, just open out.bin with a hex editor and read your keys.
They will be immediately after your IRD #.
I had to reverse the hex to use with Dish Net and left them the same order for BEV.
That's it, the Simple Jtag interface for Dummies!
Enjoy
Jim
--------------------------

[ Next Thread | Previous Thread | Next Message | Previous Message ]

Post a message:
This forum requires an account to post.
[ Create Account ]
[ Login ]
[ Contact Forum Admin ]


Forum timezone: GMT-4
VF Version: 3.00b, ConfDB:
Before posting please read our privacy policy.
VoyForums(tm) is a Free Service from Voyager Info-Systems.
Copyright © 1998-2019 Voyager Info-Systems. All Rights Reserved.